Marquetry Belt Buckles

Just over a year ago, I started making marquetry belt buckles. This past week I finished my 7th, so thought it might be time to blog about them! They are nice small projects (2" x 3") that are good for trying techniques on a small scale and have the benefit of being a cool useful item when they're done. I wear one of them almost every day, and enjoy choosing the one that fits my mood for the day.

This is my most recent one. A 1-up mushroom from Mario. I used this to try sand shading for the first time. The darkened areas of the mushroom that give it a more round look are achieved by holding the individual pieces in a pan of hot sand and basically toasting them! I also tested out a shellac finish on this one. The green material is a dyed veneer, and you have to be more careful with the finish so that it doesn't run. This was a good test, as I am working on a bigger project with similar veneer and wanted to have the process figure out before applying it to the big project. 

This was my very first belt buckle. I was hesitant to spend a lot of time cutting out a pattern, not know how it would work and how it would hold up to everyday wear. It worked better than I expected, hence making so many more. I used regular polyurethane for the finish on this one. 

This was a design I doodled one day, I thought the idea of a heart shaped gear was kind of neat. I cut it carefully and got two for one. By stacking the two colours on top of each other, the cut out of one, inserts in the other, and you get two very different looking buckles with the same design. I tried using Waterlox as a finish on these for the first time. I really liked how easy it was to apply and how durable it was as a finish. 

For these two, I used the same process to get two versions of the same design. I wanted to recreate an Escher tesselation, highlighting the main piece. So I decided to practice woodburning on veneer to outline all the surrounding flying fish. It was interesting to see how the veneer handled the wood burning and practicing how much heat and pressure to apply to get the right result. 

And then of course you may already know I'm a big Lego fan, so I decided to make a Lego Minifigure buckle. The main challenge to this one was to cut the tiny hands without them falling apart or cracking. I also got to see how to create the separation between the arms and the body by just making a cut in the wood. 

To turn these little pieces into belt buckles I buy these buckles from Amazon, and just screw them onto the back. The nice thing about this is, if I decide later I am tired of one design, I can just remove the hardware and attach it to a new buckle design!

Lightbulb Birds

This was a fun project I finished a while ago. It was from an issue of Cloth Paper scissors. I made one to their suggestion, then modified it to make the penguin. Can you guess what the base of the birds was?!

If you guessed burnt out light-bulbs, you win a prize! After this initial step a lot of paper clay covering and sculpting was involved and then painting. It was a first for me doing much of either, so it was quite a learning experience.

But I think they turned out to be pretty cute. 

And are quite the pair of feathered friends! 

Re-Purposing a Found Outdoor Table

Last month I made a short but very fun trip back home to Ottawa. We spent quite a bit of time doing projects of various sizes and shapes. This was one of the simpler ones. Earlier in the summer my Mum and Cousin came across this table on someone's lawn. It had seen better days, but my Mum had a vision!

To get it home in the car, she had to sit in the trunk holding it in, as the back of the car couldn't close. Luckily it was only a block or so away from our house! Looks like they had a pretty amusing time getting it home. 

The first problem with the table was that it was too big for the deck area and use that she envisioned. So I started by cutting a few of the boards off the top. I just used a hand saw, but it was pretty quick work. The table was made of really nice cedar which has a lot of good life left in it. 

I cut the matching boards off the other side. We did this one board at a time so we could see the size as we went to judge when it was just right. 

The next problem to address was that it was too tall. So using a square and the hand saw again, I cut each of the four legs to a better height. 

Mum seemed pretty happy with the result so far! The round edges give it some character, with it being more manageable now that it's narrower. 

Finally I trimmed the braces at an angle so they taper down from the table top to look more intentional. And we set it in place. Looked pretty good. In the spring it will get sanded and painted and be a great addition to the deck! 

Combining Turning and Marquetry - A Cavalier Tealight Holder

This was an experiment of sorts I did attempting to combine turning and marquetry. Several people in our marquetry club had shown pieces along the same lines, including plates and boxes. I decided to attempt a tealight holder. The first step was to turn the main body. I cut a small inset around the middle for the veneer, and drilled a hole in the top for the tealight. I don't seem to have any pictures, but it was the first turning I'd done in a while, so it was a bit of a challenge. 

The next challenge was laying out a design that would fit around the circumference, and that you wouldn't see the join line. I chose two Cavalier King Charles Spaniels with a butterfly. I cut them stacked, so that I actually got two copies of it, but in opposite colourways. 

Here's a more detailed shot. The height was trimmed to the exact height of the inset, and the length was slightly longer than the circumference. 

It was at this point that I realized that I'd made my life harder than necessary. While the veneer bends quiet well, especially when covered with glue, the very tight radius I'd chosen, made it very finicky to bend without it cracking. In the end, after quite a while, I got it to work. It gets glued in two stages. During the first step, I put glue on all but the last half inch on each side, to get the majority of the piece in place. When it was dry, I put a straight edge over the overlapping end bits, and made a cut with an exacto-knife through both of the pieces at once. This gives a really tight, perfect fit. I then glued the last bits. Rubber bands are the only real way to clamp it in place. I didn't have enough hands while trying to get everything aligned to take step by step photos, but am planning another similar project, where I'll show this more clearly. 

I stamped my initials in the bottom as a signature. Then added several coats of Waterlox Finish, and buffed it on the Beall Buffing system.

And this is how it turned out. I really like how no matter which way you look at it, there's something to see. So in the middle of the table, it's interesting for everyone. I definitely learned a lot doing this project, including many things I'd do differently to improve on it, and am quite excited to give it another go! 

Winnie the Pooh Marquetry Picture

So it's been a while since I've posted any projects here, but not for lack of making stuff. Things got put on hold for a bit while Jerome and I went on an epic adventure to southeast Asia! (You can click here to read more about this if you're interested) But now that we're back, and have organized all our photos I have a back log of projects that I'll be sharing over the next while. 

I thought I'd start with a pretty simple one I made for a friends baby. Growing up, I had a wood version of this image that had been my Mum's and I always thought it was so cute. So I decided to make a marquetry version. It's a very simple process, just put the two colours of veneer on top of each other, and cut through both to get the perfect fit. I glued it to some plywood, added matching veneer around the edges and back, as well as a hook hole at the back, a few coats of Waterlox and voila!